settings
SERIA D
Inginerie Mecanică
Excelență în Cercetare
Din 1929
Arhiva Online
Ani
Efficiency analysis of inflation envelope devices for upper-stages LEO deorbiting
person
Alexandru Ionel
A target recognition method using orthogonal maximum margin criterion projection
person
Xuqi Wang, Shanwen Zhang, Jian Me
Critical analysis of risk assessment methods and models used in civil aviation
person
Florin Necula
Deicing on ground optimizing process of aircraft’s
person
Sorin Eugen Zaharia, Cornel Dinu
Mathematical model for micro launcher, performances evaluation
person
Teodor-Viorel Chelaru, Alexandru-Iulian Onel, Tudorel Petronel Afilipoae, Ana-Maria Neculãescu
Recycled aggregate concrete-filled steel column convex deformation detection via non-contact measurement
person
Yunchao Tang, LijuanLi, Wenxian Feng, Chenglin Wang, Xiangjun Zou, Weiming Situ
Ignition delay period for a compression ignition engine operating on diesel and biodiesel B20
person
Mohanad Aldhaidhawi, Alexandru Racovitza, Radu Chiriac Viorel Bãdescu
Vehicle architecture optimization for pedestrian protection using finite element analysis
person
Bogdan Constantin, Daniel Iozsa, Gheorghe Frãþilã
Aspects on the capacity for double track lines with block system; compressed timetable
person
Amedeo Neculcea
Numerical study of flow and heat transfer characteristics of backward-facing step using nanofluid
person
Mohamed Bouaziz, Lotfi Bouazizi, Said Turki
Meta-heuristic approach for multi-objective optimization of condensation heat transfer and pressure drop with twisted tape inserts
person
Ravindra Kumar, Parmanand Kumar
A study on development of steam generator for domestic steam cleane
person
Feng-Xun Li, Zhen-Zhe Li
Analyse de la correlation entre la rugosité et la vibration de coupe en usinage des aciers durcis
person
Youcef Abidi, Lakhdar Boulanouar
Soret and heat source effects on MHD flow of a viscous fluid in a parallel porous plate channel in presence of slip condition
person
Malapati Venkateswarlu, Meduri Phani Kumar
A comparative study of CAD data exchange based on the step standard
person
Sa¹a Ãukoviæ, Goran Deved¾iæ, Michele Fiorentino, Ionut Ghionea, Nabil Anwer, Lihong Qiao, Bojan Rakonjac
Selection of drill for drilling with high pressure coolant using entropy and copras MCDM method
person
Jelena Stanojkoviæ, Miroslav Radovanoviæ
Investigation on dynamic behaviour of sandwich panels made of aluminium and hybrid polymer and optimization of design parameters using Taguchi method
person
G. Venkatachalam, Vipin Venu, Vignesh P, Karan Ghule, Jasbir Singh Saluja
Fault diagnosis of rolling bearing based on TKEO-ELM
person
Jun Ma, Jiande Wu, Xiaodong Wang
Experimental research on structural hardening of the maximum stressed crankshafts surfaces obtained by thermal spraying
person
Alina Elena Bușaru, Mariana Goran, Roxana Alexandra Gheța, G. M. Dumitru, G. Iacobescu
Simulation of the cyclic hardening behavior of aluminum alloys
person
Tayeb Kebir, Mohamed Benguediab, Abdelkader Miloudi, Abdellatif Imad
The complex stiffness method of damping for constrained damping structure with a stand-off layer
person
Wenjun Zhang, Dagang Sun, Bijuan Yan, Zhanglong Li
Interlaboratory comparison of a digital thermohygrometer in several Romanian laboratories
person
Andreea-Diana Moroºanu, Gabriel Marius Dumitru, Gabriel Iacobescu, Dumitru Marius Neagu, Cosmin Dinu
Modelling the degradation of organic matter in wastewater
person
Liana Ioana Vuta, Gabriela Elena Dumitran, Vlad Florin Piraianu
Three-dimensional simulation of pollutant dispersion of an open channel flow with a side discharge
person
Alhassan H Ismail, Diana Robescu
Air fractions impact over pressure drop in air-water mixture flow
person
Corina Boncescu, Diana Robescu
Dynamics of the electrohydraulic servopumps for industrial open circuits
person
Georgiana Claudia Vasiliu, Daniela Vasiliu, Marius Daniel Bontoș
Modeling the decision-making process in order to assess the risks of an IT&C project
person
Teodor Beleþ, Anca Alexandra Purcãrea, Olivia Doina Negoita, Mihai Corocaescu